First remove the 4 nuts holding the s bend on
Next remove the 4 bolts holding the manifold to the charger
Next take a rubber mallet and take your time tapping them apart, this is about what you will end up with. I had already taken off the pressure relief valve.
Next remove the 4 bolts that hold the pressure relief valve assembly
Next Remove the Oil filler bolt and drain the Castor Oil out.
Next remove the 8 10mm bolts and tap with a rubber mallet until it separates like so. Notice the rubber coupler is pretty worn!
Next Tap the rotor assembly loose from the rotor housing and you'll end up with this
Coming up next is bearing replacement, btw it turns out some of the bearings cant be replaced except by Magnuson!
I know! Hopefully this thing turns into a beast, all I need now is a rising rate FPR 5 to 1 ratio, thermal gasket, rebuild kit for the charger, walbro 255, and my chipped p28! Just about $400
what are you thinking about for how many pounds?????......looking good so far.
I was thinking about 8 lb's max becuase i have a dead stock d16a vtec. BTW Ka8 is there any chance I could get you to take some really good pictures of where you have all your vac lines run?
Just started working through some minor things on the engine and realized I had somehow been off one tooth the whole time :shock: . SO I am in the middle of working on that and I adjust the idle without jumping my timing calibration and now it's running like crap! Does anyone know the procedure on how to adjust the idle by the book? I cant seem to locate mine.
New Goodies going in tonight!
Skunk2 shocks and i have a set of skunk2 coilovers also, and yes those are blackworks lca's. You cant get Lca's wrong and at $69 it was an awesome deal!
So I installed the shocks and everything sit's up high while I'm riding on bump stops. I know i didnt install them wrong anyone got a clue of whats up. I bought a set of shocks for an 89 civic and coilovers too! :x
Is everything sitting high? You're gonna have to really slam the rears to make them level with the fronts.
As far as bumpstops go...tophats ftw?
Agreed, This isnt exactly the best setup but it is nice and it definatley needs a set of top hats for the lowered look without a funky rides. Also Turns out they shipped me a set of DA integra shocks!
Comments
Dissasembly!
First remove the 4 nuts holding the s bend on
Next remove the 4 bolts holding the manifold to the charger
Next take a rubber mallet and take your time tapping them apart, this is about what you will end up with. I had already taken off the pressure relief valve.
Next remove the 4 bolts that hold the pressure relief valve assembly
Next Remove the Oil filler bolt and drain the Castor Oil out.
Next remove the 8 10mm bolts and tap with a rubber mallet until it separates like so. Notice the rubber coupler is pretty worn!
Next Tap the rotor assembly loose from the rotor housing and you'll end up with this
Coming up next is bearing replacement, btw it turns out some of the bearings cant be replaced except by Magnuson!
I know! Hopefully this thing turns into a beast, all I need now is a rising rate FPR 5 to 1 ratio, thermal gasket, rebuild kit for the charger, walbro 255, and my chipped p28! Just about $400
I still wish vortech made a D-series kit!
I was thinking about 8 lb's max becuase i have a dead stock d16a vtec. BTW Ka8 is there any chance I could get you to take some really good pictures of where you have all your vac lines run?
IDK if a lil D can handle a vortech lol,
If you bolted a vortech on a LIL D it would be WHAT THE FUCK BOOOOOOOOOOOM!!!!!!!!!
The torque is really nice in a jackson and i wanted something very simple that didn't require me to fiddle with my AC!
Also, I'm in the middle of my z6 vitara build and will have my JRSC sometime next week
Skunk2 shocks and i have a set of skunk2 coilovers also, and yes those are blackworks lca's. You cant get Lca's wrong and at $69 it was an awesome deal!
As far as bumpstops go...tophats ftw?
Agreed, This isnt exactly the best setup but it is nice and it definatley needs a set of top hats for the lowered look without a funky rides. Also Turns out they shipped me a set of DA integra shocks!
x2
I might get done with my build before you!
Maybe, You Should see all the goodies I just bought! Holy Hell Balls I spent ALOT!