How To Install Rear Foglights?

13»

Comments

  • ThaClutcHThaClutcH Senior Wagonist
    Thanks. Thats gonna come in handy.
  • ragenasianragenasian Moderator
    So there is enough space for the metal bracket. Good to know. Sometimes they are too rusted to use over here.

    Good info! Is this a sticky yet?
  • HaydzHaydz Moderator
    ragenasian wrote:
    So there is enough space for the metal bracket. Good to know. Sometimes they are too rusted to use over here.

    Good info! Is this a sticky yet?

    Nah no stickys anymore just add it to the Quicklinks thread at the top of the sub-forum.
  • Eagle BeagleEagle Beagle familEE
    imho that construction is also designed to reduce vibration
    that could damage wires and the metal filament of lightbulbs

    : )
  • wagodizzlewagodizzle Council Member and EDM expert
    ragenasian wrote:
    So there is enough space for the metal bracket. Good to know. Sometimes they are too rusted to use over here.

    Good info! Is this a sticky yet?

    when i installed mine i had to cut out a piece of my bumper support, because with it in place the rear fog would pop out a good 1.5 inches.

    but i had SH3 (Hatchback fogs) on mine.
  • unlimited02unlimited02 Senior Wagonist
    does anyone know a security method to stop jackers from pulling it out...?
  • slide7229slide7229 Wagonist
    :oops: is there any way to wire them to indicators and reverse lights??? im not good with electricity at all
  • unlimited02unlimited02 Senior Wagonist
    what i did was connect to the rear tailights but so when i turn on my lights it comes on... dont put it on ur break light b/c everytime u break it well come on...
  • t.kt.k New Wagonist
    I don't mean to bump an old thread but I wanted to know if anyone got the position measurements for the fogs, or do most people just eyeball the position? Install doesn't seem hard I just want to make sure the position of the fogs are as close to OEM as possible. Any information or links to resources is greatly appreciated!
  • BillBoardBillBoard council member
    t.k wrote: »
    I don't mean to bump an old thread but I wanted to know if anyone got the position measurements for the fogs, or do most people just eyeball the position? Install doesn't seem hard I just want to make sure the position of the fogs are as close to OEM as possible. Any information or links to resources is greatly appreciated!

    there should be outlines on the inside of your bumper on where to cut... page 2 some one actuall took a picture, just a little bit of reading, not even reading just looking at the picture... come on!
  • CharbCharb Administrator
    I made my first meme! paintshop ftw! lol





    Wish this thread was lockable after that. Too much good info. I will quick link it though...
  • BillBoardBillBoard council member
    ^lols too awesome...
  • t.kt.k New Wagonist
    BillBoard wrote: »
    there should be outlines on the inside of your bumper on where to cut... page 2 some one actuall took a picture, just a little bit of reading, not even reading just looking at the picture... come on!

    I wasn't sure if the outlines are on all models or not, thanks!
    Charb wrote: »
    I made my first meme! paintshop ftw! lol





    Wish this thread was lockable after that. Too much good info. I will quick link it though...
    mynewavi.jpg
  • TheGreatBaconTheGreatBacon Wagonist
    Through trouble shooting I answered my own question.. I had a crx harness on my hatchback fogs, the red and blue wire went to the fog light switch. The switch works perfect otherwise. Thanks for the write up evol911
Sign In or Register to comment.

© Vanilla Keystone Theme 2025