My Honda Shuttle EE4 with JRSC

SaXXXonSaXXXon New Wagonist
in Rides & Builds- Civic wagons
Hi guys since i was not able to edit my first thread after the forum upgrade, and this is a new car i thought i could start a new project thread :)

A user on the Norwegian Honda forum (CHN.no) that i know pretty well needed to sell his Shuttle to get money for his new hobby (shortcars)
and since my old Shuttle was soooo full of cancer that there was no hope. i went over to the other side of Norway and picked me up a new one :)

Pros
- Jackson Racing Supercharger kit
- With custom pulley on the charger and a D16Y8 pulley on the engine equals around 9 PSI. OBD2 pulley on the power steering to make things fit.

- Custom 4-2-1 header to clear the transfer case

- Innovate Motorsports LC-1 lambda and gauge

- Civic gen. 5 radiator

- Road mapped with TurboEdit and Moates emulator

- alot of ES poly bushings

- Civic front springs in the rear for more fun in the winter


Cons
- weird grinding noise in reverse

- left drive axel has some noise

- oem cluch

- goes into safe mode in 1 in 50 engine starts, (most likely the Moates emulators fault)

- rear hatch is reaaaally rusted.

- some dings and scratches


Plans
- MOT

- Paint

- Get some on the norwegian forum to burn me a chip

- Wheels (need tips here, was going to buy Diamond Racing Wheels, since this is a budget build, but i hear that some says quality sucks and they are really slow on answering emails)

- have some coilovers waiting for it

- buy camber kit (do i need it? which one? )

- New steering wheel

- Rear mid wing


Pictures

145.jpg
Honda Shuttle v2 by Jone K. Overland, on Flickr

146.jpg
Honda Shuttle v2 by Jone K. Overland, on Flickr

147.jpg
Honda Shuttle v2 by Jone K. Overland, on Flickr

148.jpg
Honda Shuttle v2 by Jone K. Overland, on Flickr

467.jpg
in the shuttle by Jone K. Overland, on Flickr
«1

Comments

  • GeorgieGeorgie Wagonist
    Heated Seats, FTW.
  • DRMORTYDRMORTY Council Member
    Never seen the heated seat buttons before.. Kinda Cool.. But, I doubt I'd use them in Florida.
  • SaXXXonSaXXXon New Wagonist
    think ive finally set on some wheels.

    Enkei 92s in Silver.

    831.jpg

    you guys approve?
  • josh1vtmjosh1vtm Council Member
    Those enkeis will look nice but i saw on there that you were looking to get some diamond racing steelies but youre worried about the quality. Some of tyhe stuff youve heard is true, older sets of them are fine but newer sets are outsourced to china for a cheaper product and cheaper quality. But if youre still wanting a custom set of steelie style wheels check out circletracksupply.com or circletrackimports.com. the owner is Chaife(he got wagon of the month this month in his 3rd gen). Check out my thread and you can see what a set of them look like, and we are about to put a set with beadlocks on chips(3rd4ce) wagon that we are helping him work on
  • SaXXXonSaXXXon New Wagonist
    Thanks alot for the answer :) i will check that out! will try keep you guys updated :)
  • SaXXXonSaXXXon New Wagonist
    picked up some parts on my roadtrip crosscountry which is featured in my CRX thread.

    268.jpg
    new parts by Jone K. Overland, on Flickr

    269.jpg
    new parts by Jone K. Overland, on Flickr

    270.jpg
    new parts by Jone K. Overland, on Flickr

    271.jpg
    Untitled by Jone K. Overland, on Flickr

    272.jpg
    Untitled by Jone K. Overland, on Flickr


    also had time to tear out some more stuff from my old car

    273.jpg
    tear down by Jone K. Overland, on Flickr

    engine and drivetrain left

    274.jpg
    teardown by Jone K. Overland, on Flickr
  • wagodizzlewagodizzle Council Member and EDM expert
    i see you found a set of heated seat switches :) nice!
  • SaXXXonSaXXXon New Wagonist
    Wheels arriving tomorrow :) now i'm trying to find out what more parts i need to get my KSport Coilovers to fit. they are made for my 91 CRX

    do i need new LCAs? cant find any clear answers..
  • SaXXXonSaXXXon New Wagonist
    Brought it to its first mini street meet yesterday

    744.jpg
    Meeting Point in Stavanger by Jone K. Overland, on Flickr

    745.jpg
    Meeting Point in Stavanger by Jone K. Overland, on Flickr

    746.jpg
    CHN street meet by Jone K. Overland, on Flickr
  • MyFirstWasAnEF9MyFirstWasAnEF9 Wagonist
    Its cool to see whats going on across the world. Really nice find on your wagon keep up the good work. In my experience I have found to get suspension to fit you have to change the top hats or lca's like your thinking. I would get either after market or Si ones then you can add a rear swaybar too.
  • SaXXXonSaXXXon New Wagonist
    great to hear. there's some activity just in a muuuuch smaller scale. so i dont need both? the Blox ones for the CRX looks like a good and not to expensive part
  • black_89gtblack_89gt Wagonist
    89-91 CRX should be a direct swap for 89-91 wagons, since you have the 91 CRX coilovers and a 91 wagon they should bolt right up, there shouldn't be a difference between EDM and USDM I don't think. (I have coilovers for 89-91 CRX on my 90 wagon). The ones that are different are pre-88 and you have to get different LCA's because the bottom mounts on the rears are different.

    To make sure look at the LCA's you have on the shuttle and if the mounting looks the same as your coilovers, then they should work.
  • SaXXXonSaXXXon New Wagonist
    damn delivery guy didnt show up until now!! its two hours till midnight here!

    759.jpg
    New Wheels by Jone K. Overland, on Flickr

    760.jpg
    New Wheels by Jone K. Overland, on Flickr

    761.jpg
    Enkei by Jone K. Overland, on Flickr
  • AlaskaB16AlaskaB16 New Wagonist
    So clean!!!
  • SaXXXonSaXXXon New Wagonist
    Rear Camber and Toe Kit on its way
  • SaXXXonSaXXXon New Wagonist
    465.jpg
    parts by Jone K. Overland, on Flickr

    now i just need the silicone hoses for my CRX so i have something to drive while i strip down the Shuttle for paint
  • SaXXXonSaXXXon New Wagonist
    Since the silicone hoses for my CRX is still stuck in customs i can't get started on the new parts and rest of the work to get the car ready for paint.

    but!

    these badboys arrived :)
    243.jpg

    and also i've been really fighting with my wideband lamda. i cant get any readouts on it. anyone have any tips? its a Innovate Motorsports LC-1
  • HakosukaHakosuka Wagonist
    pardon me, i thought this was the marketplace for a minute
  • wagodizzlewagodizzle Council Member and EDM expert
    Shuttle is looking clean! Going to be sick with those wheels :)
  • SaXXXonSaXXXon New Wagonist
    Thanks 503wagon for cleaning up :)

    im hoping the same. may get to testfit them within a couple of weeks
  • SaXXXonSaXXXon New Wagonist
    from the video from the trackday i went on. a 3000km roadtrip to drive some NSX :)

    373.jpg
    sundown at dovrefjell by Jone K. Overland, on Flickr


    check out a friends video from the track
    https://vimeo.com/51460104
  • codyJDMcodyJDM Wagonist
    SaXXXon wrote: »
    465.jpg
    parts by Jone K. Overland, on Flickr

    now i just need the silicone hoses for my CRX so i have something to drive while i strip down the Shuttle for paint

    in this pic theres 1 '89-'91 style mount rear coilover, and 1 '88 style mount rear coilover? whats up with that?
  • SaXXXonSaXXXon New Wagonist
    thats the front damper. different bottom ends are in the set. havent changed them yet
  • jasnalljasnall Wagonist
    what ECU are you using?
  • SaXXXonSaXXXon New Wagonist
    jasnall wrote: »
    what ECU are you using?
    not sure which version, i'll have to check. but it's fitted with this http://www.xenocron.com/demon-eprom-emulator-and-datalogging-hardware-p-461.html

    just passed MOT and the wagon is almost ready for winter now. that means it's lowered :P now i just need to fit the winter tires and maybe the big ass driving lights again.

    and maybe i should get a front lip? suggestions?
  • 949949 Senior Wagonist
    your o2 sensor might be shot. those go out pretty fast.
  • wagodizzlewagodizzle Council Member and EDM expert
    USDM '95-'96 Accord front lip. that's what you should get :)
  • SaXXXonSaXXXon New Wagonist
    wagodizzle wrote: »
    USDM '95-'96 Accord front lip. that's what you should get :)

    ebay is the place to get it?
  • SaXXXonSaXXXon New Wagonist
    Finally got a new clutch and the tranny from the parted out car into it. holy c*** that was a frustrating job!
  • wagodizzlewagodizzle Council Member and EDM expert
    SaXXXon wrote: »
    ebay is the place to get it?

    I could also get you one here and mail it!
Sign In or Register to comment.

© Vanilla Keystone Theme 2025